Product Documents

JOES Caster / Camber Gauge Instructions

JOES Caster / Camber Gauge Instructions

#28201, #28203, #28205, #28209 & #28210

Important:Your JOES caster/camber gauge is a precision measuring instrument and should be handled with care. It should be stored in a cool, dry place and should never be left sitting in the direct sun light. Vial breakage may occur at temperatures over 120° F.

Instructions

  • Caster and Camber must be measured with the car on a flat, level...read more »

#54005 JOES Pro Probe Pyrometer Instructions

PRO Probe Pyrometer P/N 54005

JOES Pro Pyrometer is a portable 3-1/2 digit, compact-sized digital pyrometer designed to use external K-type thermocouple as the temperature sensor. Temperature indication follows National Bureau of Standards and IEC584 temperature/voltage tables for K-type thermocouples. One JOES adjustable K-type thermocouple is supplied with the pyrometer.

Set the stop on your probe to match the rubber thickness on your tires. For accurate readings...read more »

#32311 JOES Precision Air Tire Pressure Gauge Instructions

#32125 JOES Purge & Prep Tool Instructions

#32125 JOES Purge & Prep Tool Instructions

#28295 JOES Digital Bump Steer Gauge Instructions

#28295 JOES Digital Bump Steer Gauge Instructions

  • Set the air pressure, stagger and place the car at ride height.
  • Adjust the caster and camber.
  • Match your tie rod lengths per the 1-2-3 instructions below and set the toe.
  • Center the steering by centering the inner tie rod ends with the Lower Control Arm inner pivot per the 1-2-3 instructions. Lock the steering in place.
  • Record a reference point while your car is on the ground and...read more »

#28252 JOES Dunlop Caster / Camber Gauge Instructions

#28252 JOES Dunlop Caster / Camber Gauge Instructions

Important:Your JOES caster/camber gauge is a precision measuring instrument and should be handled with care. It should be stored in a cool, dry place and should never be left sitting in the direct sun light. Vial breakage may occur at temperatures over 120° F.

Instructions

  • Caster and Camber must be measured with the car on a flat, level surface.
  • The car should be...read more »

#25880, 25885, 25888 & 25890 Micro Sprint Motor Mount Instructions

#17035 JOES Brake Balance Adjuster Installation Instructions

#17035 JOES Brake Balance Adjuster Installation Instructions

New cable style design! Retrofit Cable kits are available (#17037).

  1. Attach the cable fitting to your brake balance screw on your pedal assembly. (We supply two fittings for different size screws)
  2. Mount the Brake Balance Bracket and cut the 1/4" solid handle rod to your desired length. The handle rod...read more »

#12950 & #12096 JOES Window Net Mounting Kit Installation Instructions

#12950 & #12096 JOES Window Net Mounting Kit Installation Instructions

  1. Start with the top rod. Use 2 of the supplied steel tabs to begin the mounting process. The Red handle is removable and will be located to the rear side of the driver’s window. Locate the front tab and layout the net placement being sure that there is room for the spring action. Leave clearance between the window net, red handle and roof roll bar.
  2. With the top rod properly...read more »

#11950 JOES Sway Bar Mount Installation Instructions

#11950 JOES Sway Bar Mount Installation Instructions

  1. Locate the JOES Sway Bar mounting system so that the linkage between your sway bar and your lower control arm are as close to 90 degrees as possible. Since it is simple to slide the JOES Sway bar mount on the frame rail be sure to spend the time to ensure your links/chains are as close to 90 degrees as possible.
  2. Typically, the sway bar bolt...read more »

#11475 JOES Rear Mount & Caliper Mount Installation Kit Instructions

#11475 JOES Rear Mount & Caliper Mount Installation Kit Instructions

  1. Consult your car builder for the pinion angle and distance from the rotor for your Rear Mount. For the caliper mount, install the caliper centered on the rotor and tighten the JOES Caliper Mount per you car builder recommendations.
  2. Set your rear end in the car on blocks, at ride height and at your car builder recommended...read more »

#11402 JOES Rear Mount Installation Instructions

#11402 JOES Rear Mount Installation Instructions

  1. Consult your car builder for the pinion angle and distance from the rotor.
  2. Set your rear end in the car on blocks, at ride height, at your car builder recommended pinion angle.
  3. Clamp the JOES Rear Mount in place, matching your car builder specs for spacing to the rotor.
  4. There are 2 methods for positive anti rotational mounting:...read more »